- SETTING UP CETUS3D IN UPSTUDIO SOFTWARE
- SETTING UP CETUS3D IN UPSTUDIO CODE
- SETTING UP CETUS3D IN UPSTUDIO PC
- SETTING UP CETUS3D IN UPSTUDIO FREE
If you have any questions or still need help feel free to reply. The only flaw with this theory is that if this is the issue you should have been seeing PLA backlog and come out the back the extruder. This could actually be causing the issue as the filament doesn’t get guided In correctly. I personally have the the extruder without the silicon tube that guides the filament sticking out of the extruder, I use the nozzles that have it cut off. For PLA it is typically between 180° and 220☌. Make sure that your temp is in the manufactures recommended range. Make sure that you have the corresponding setting for the nozzle you have placed.(0.4 nozzle, 0.4 nozzle setting) The printer(Cetus3D) is sadly made to basically only run on UpStudio or the beta ‘Catfish’, meaning that unless you make some serious modifications like u/unmotivatedgene or u/thecaptain78 you are probably going to struggle greatly with getting cura working on your printer. With under extrusion raising the temp really wont do that much as long as you are following the filaments manufactures recommend temp.īefore I get into possible issues in solutions I just quickly want to talk about Cura. I have better results with lower flow rates (dia 0.4 or 1900%), but more testing needs to be done.Ok.
SETTING UP CETUS3D IN UPSTUDIO SOFTWARE
Filament diameters of around 0.38 translate to the 2200% cmeyer posted (flow rate factors in quadratic, so use fine steps when adjusting it). Open the Tiertime Software on the computer next to the 3D printers Choose up. Flow rate percentage adjustments mess up the ‘layer view’ in Cura (from years of experience with an Ultimaker 2, I find this one of the most helpful features in Cura). Keep in mind that you may have to find a physical solution for levelling the build bed when using Cura.ĭ) With the current version of Cura (v3.3.1) it is better to adjust the flow rate of molten filament via the filament diameter, than the flow rate percentage. The nozzle is too far away from the bed, if the individual lines can be easily separated and do not stick together.)Ĭ) Up Studio allows for an 9-point calibration routine for the z-axis. The nozzle is too close to the bed, if the brim thickness (z-direction) gets to thin and translucent. If you use a brim around a test-model in Cura, the correct height is achieved, if the individual lines that make up the brim squash together nicely. (I think a painfully precise calibration is overkill.
SETTING UP CETUS3D IN UPSTUDIO CODE
I did compile my ‘own version’ from the start code by chrisevich. For Windows use UP Studio(its exactly the same) Open Cetus 3D and go to Print Add your file or test printer with a simple geometry Set print. Perhaps the info below will help someone in the future:Ī) I used the start and end code from chrisevich ( #11) which worked nicely for me.ī) the z-axis calibration code posted by cmeyer never worked for me. I just wanted to thank everyone who contributed to this thread - it helped me tremendously when setting up my Cetus3D MkII with Cura. G1 X50 E360 F300 extrude a 5cm purge line
G1 X2 Y178 F5000 move to back right corner M206 X-180 offset X axis so the coordinates are 0.180, normally they are -180.0 Do the paper test and use a gcode file something like this:p.p1 the nozzle offset may be different than in Cetus Studio.
Find my logs and a support mail from Cetus3D in the docs directory. When I shared a short video with Cetus3D support, I got an OK to publish this, and even a bit of support.
SETTING UP CETUS3D IN UPSTUDIO PC
The 1st generation had some flaws but printed decent, especially with their proprietary software Cetus3d which is now known as Up Studio. Using the standard Cetus3D PC software (now UP Studio from Tier Time) and WireShark and a lot of experiments, I was able to reverse engineer the communication between UP Studio and my Cetus3D. make sure your nozzle offset is correct in the starting g-code I was initially hesitant until I found out that Cetus3d is a subsidiary of Tiertime, who has been making 3D printers since 2003.
0 kommentar(er)
